HVAC technician in a hard hat standing beside a Westchester HVAC Pros service van

Home / HVAC Tips

Boiler Not Heating? What to Check Before You Call

A cold house with a boiler in the basement is a common winter problem across Westchester County. Here are the safe checks a homeowner can make, the signs that point to a deeper problem, and the steps to leave to a licensed HVAC technician.

Why is my boiler not heating?

When a boiler is not heating, the cause is often something simple: the thermostat is not calling for heat, the boiler’s power switch is off, a breaker has tripped, or the valves on the radiators or baseboard units are closed. If those all check out and the house is still cold, the problem is inside the boiler or its controls, and a technician needs to find it.

Start at the thermostat

A boiler only runs when something tells it to. In most homes that signal comes from the thermostat, so it is the first place to look. Make sure it is set to heat, not cool or off, and turn the setpoint a few degrees above the current room temperature.

Many thermostats run on batteries, and a weak battery can leave the screen looking normal while the thermostat stops sending a call for heat. If the display is blank, faint or flashing a low-battery symbol, put in fresh batteries and give the system several minutes to respond. Some thermostats are wired to the boiler and have no batteries at all; if yours has a blank screen and no battery compartment, check the breaker and boiler switch next.

  • Mode set to heat
  • Setpoint above the current room temperature
  • Fresh batteries if the display is weak or blank
  • Any schedule or hold setting not overriding your change

Check the boiler switch and the breaker

Most boilers have a service switch near the unit or at the top of the basement stairs. It often looks like an ordinary light switch, sometimes with a red cover plate, and it is easy to flip off by accident. Make sure it is in the on position. If the boiler has its own small display, check whether it shows power at all once the switch is on.

Next, go to your electrical panel and look for a tripped breaker labeled for the boiler or the heating system. A tripped breaker sits in the middle or off position. Reset it once. If it trips again, leave it off and call for service, because something is drawing too much current.

Radiator cold or baseboard heat not working in one room

If the boiler runs and most of the house warms up but one radiator or one stretch of baseboard stays cold, the problem may be local to that room. Check that the valve on the radiator or baseboard unit is open. Valves get turned off during cleaning, painting or a summer of trying to cool a room, and then forgotten.

Also make sure nothing is blocking the heat. Furniture pushed tight against a radiator, heavy curtains over baseboard units and covers packed with dust all reduce how much warmth reaches the room. If the valve is open and the unit is clear but it still stays cold, have a technician check it. Air trapped in the system and circulation problems are common causes, and they should be handled by someone with the right tools and training.

When the whole boiler is not turning on

If the thermostat is calling for heat, the switch is on, the breaker is fine and the boiler is still silent, the cause is inside the equipment. It could be an ignition problem, a failed control, a safety switch that has shut the boiler down, or a circulation issue. A boiler can also run and still fail to deliver heat if water is not moving through the pipes.

Signs worth noting before you call: any error code or blinking light on the boiler, unusual banging or gurgling, water on the floor around the unit, or a boiler that starts and stops repeatedly. Write down what you see. It helps your technician narrow things down.

  • Error codes or blinking lights on the control panel
  • Banging, gurgling or whistling noises
  • Water pooling around the boiler
  • The boiler starting and stopping over and over

What not to do with a boiler

Some advice online tells homeowners to bleed radiators, drain or refill the boiler, relight a pilot or reset safety controls. Those steps involve hot water under pressure, fuel and safety devices that exist to prevent serious harm. Leave them to a licensed HVAC technician.

Do not press the reset button on a boiler more than once, and do not try to bypass any switch that keeps shutting it off. A safety control that trips is telling you something is wrong, and forcing the boiler to run can make that problem worse.

Westchester boiler homes and what a repair visit covers

Boilers with radiators or baseboard heat are common in older houses throughout the county, from the multi-family homes of Mount Vernon to the colonials of Hastings-on-Hudson and Briarcliff Manor. Many of these systems have been running for a long time and have been modified more than once over the years.

On a repair visit, your technician checks the controls, ignition, circulation, pressure and safety devices to find out why the boiler is not heating. You hear what failed and whether a repair makes sense, or whether the boiler is near the end of its life and replacement is worth considering. You get an estimate before work starts.

Gas smell and carbon monoxide safety

If you smell gas or a rotten-egg odor near the boiler or anywhere in the house, do not flip switches or use a phone indoors. Leave the home with everyone in it, and call 911 or the gas utility from outside. Every home with fuel-burning heat should have working carbon monoxide alarms on each level and near sleeping areas. If a carbon monoxide alarm sounds, get everyone outside and call 911.

Keep reading

Related services and guides

If your boiler needs more than a quick check, these pages explain the work involved.

Boilers and Radiators

Boiler repair in Westchester NY for cold radiators, baseboard heat problems, noises and leaks. A licensed HVAC technician diagnoses it. Contact us today.

Boilers and Radiators details

No Heat or No Cooling

No heat repair in Westchester NY, plus no cooling repair in summer. Safe checks to try first, then a licensed HVAC technician finds the cause. Contact us.

No Heat or No Cooling details

Seasonal Tune-Ups

HVAC tune-up in Westchester NY: AC checks in spring, furnace and boiler service in fall. A licensed HVAC technician inspects, cleans and tests. Book now.

Seasonal Tune-Ups details

Boiler still not heating?

If you have made the safe checks and the house is still cold, contact us. A licensed HVAC technician will come out, find the cause and explain your options.

(914) 353-4574

FAQ

Common Questions

Why is my boiler running but the radiators stay cold?

The boiler may be heating water that is not circulating through the pipes, or air may be trapped in part of the system. A failed pump or a stuck valve can do the same thing. A technician needs to check circulation and controls to find the cause.

Should I bleed my radiators myself?

We recommend leaving it to a technician. Bleeding involves hot water and system pressure, and releasing air without checking the boiler’s pressure afterward can create a new problem. A technician can handle it safely as part of a service visit.

Is it safe to keep resetting my boiler?

No. If the boiler shuts off and needs a reset more than once, a safety control is responding to a real problem. Leave it off and call for service.

More answers: heating and cooling FAQ

Contact us

Talk With a Licensed HVAC Technician