HVAC technician working on the controls of a furnace in a basement

Home / Services / Furnace Repair

Furnace Repair in Westchester NY When the Heat Will Not Keep Up

A furnace that blows cold air, cycles on and off, or quits halfway through a cold night needs a proper diagnosis, not guesswork. A licensed HVAC technician will find what is failing, explain it and repair it once you approve.

What should I do when my furnace is not working?

First check the thermostat, the furnace power switch, the breaker and the air filter, since those cause a surprising number of no-heat calls. If those are fine, the problem is likely inside the furnace, such as an ignition, flame sensing, blower or safety switch issue, and a technician needs to diagnose it. For furnace repair in Westchester NY, contact us. If you smell gas, leave the home first and call 911 or your gas utility from outside.

How we approach it

How a furnace repair is diagnosed and fixed

Furnaces have several safety controls built in, so a careful diagnosis matters as much as the fix itself.

Confirm the symptoms

Your technician watches the furnace try to start and notes exactly where the sequence stops.

Test the components

Ignition, flame sensing, safety switches, blower, venting and controls are checked one by one.

Lay out options

You get the cause in plain terms and a clear estimate before any part is replaced.

Repair and verify

After the repair, the furnace runs through several full cycles to confirm it heats and shuts down safely.

HVAC technician in a hard hat standing beside a Westchester HVAC Pros service van

What to watch for

Signs your furnace needs repair

Some furnace problems announce themselves loudly. Others creep in over a few weeks. Either way, these are worth a call.

  • Cold or lukewarm air coming from the vents
  • The furnace starts, runs briefly, then shuts off again
  • Repeated clicking with no flame or no heat
  • Some rooms warm while others stay cold
  • New rumbling, squealing or banging when the furnace runs
  • The blower runs constantly or never comes on
HVAC technician checking gauges on an outdoor air conditioner condenser

Furnace Repair

Why furnaces short-cycle, shut off or blow cold

A modern furnace runs through a set sequence every time it starts: the thermostat calls for heat, a draft fan clears the vent, the igniter lights the burners, a sensor confirms there is a flame, and then the blower sends warm air through the ducts. If any step fails, the furnace stops and tries again, or locks itself out. That is why a furnace not working can look the same from the outside even when the causes are very different.

Short-cycling, where the furnace runs for a minute or two and shuts down, is often tied to air flow. A clogged filter or closed-off vents can let the heat exchanger get too hot, and a safety switch shuts the burners off to protect it. A dirty flame sensor is another frequent culprit: the furnace lights, does not detect the flame, and shuts off within seconds. Venting problems, a failing draft fan or a cracked component can also trigger shutdowns, and those need careful testing.

Cold air from the vents can mean the burners never lit, the furnace locked out after several failed tries, or the thermostat fan setting is on instead of auto. Your technician sorts out which is happening before recommending a repair, so you are not paying to replace parts that were never the problem. Many furnaces also store a fault code or blink a status light when they lock out. You do not need to open anything to see it, but if you notice a blinking light through the small window on the front panel, mention it when you call.

Good to know

Gas safety and carbon monoxide: read this first

If you smell gas or a rotten-egg odor anywhere in the home, do not try to find the source and do not touch the furnace. Do not flip light switches, unplug anything or use a phone inside. Get everyone out of the house, then call 911 or your gas utility from outside. Wait for them to say it is safe before going back in.

Every home with a gas furnace should have working carbon monoxide alarms, ideally near sleeping areas and on each level. If an alarm sounds, leave the home and call 911 from outside. Headaches, dizziness or nausea that ease when you leave the house are also a reason to get out and call for help.

The safe homeowner checks are simple: confirm the thermostat is set to heat and above the room temperature, replace its batteries if needed, make sure the furnace power switch (it often looks like a light switch near the unit) is on, check the breaker and replace a dirty filter. Do not remove furnace panels, relight anything or touch the gas valve. Beyond those checks, heating repair belongs in a technician’s hands.

Related services

Related heating services

If your heating problem is bigger than one repair, or involves a different system, these pages may help.

Furnace Replacement

Furnace replacement in Westchester NY, planned around your home, ducts and venting by a licensed HVAC technician. Request an estimate for a new furnace.

Furnace Replacement details

No Heat or No Cooling

No heat repair in Westchester NY, plus no cooling repair in summer. Safe checks to try first, then a licensed HVAC technician finds the cause. Contact us.

No Heat or No Cooling details

Thermostats

Thermostat repair in Westchester NY and new thermostat installation matched to your wiring and equipment, done by a licensed HVAC technician. Contact us.

Thermostats details

Helpful guides

Quick checks before you call

Boiler Not Heating

Boiler not heating? Safe checks for cold radiators and baseboard heat in Westchester NY homes, and when to call a licensed HVAC technician.

Boiler Not Heating guide

Service area

Heating repair in White Plains and the rest of Westchester County

We are based in White Plains and repair furnaces in homes all over Westchester County. That includes split-levels in Greenburgh and Ardsley, colonials in Briarcliff Manor and Pleasantville, and homes on the larger lots of Mount Kisco and Bedford. Winters here are long and cold, so if your furnace is acting up, contact us early rather than waiting for the first freezing night. See the towns we serve.

Get your furnace looked at

Tell us what the furnace is doing and where in Westchester County you live. A licensed HVAC technician will find the cause and explain the repair.

(914) 353-4574

Furnace Repair FAQ

Common Furnace Repair Questions

Why is my furnace blowing cold air?

The burners may not be lighting, the furnace may have locked out after failed starts, or the thermostat fan may be set to on. A technician needs to check the start-up sequence to find the actual cause.

Can I reset my furnace myself?

You can check the thermostat, breaker, power switch and filter. Repeatedly resetting a furnace that keeps locking out is not a good idea, because the lockout usually means a safety control has found a problem.

What does it mean if my furnace keeps shutting off?

Short-cycling is often caused by a clogged filter, a dirty flame sensor, a venting problem or an overheating safety switch. Your technician will test each possibility before recommending a repair.

What should I do if I smell gas near my furnace?

Leave the home right away without using switches or phones inside. Call 911 or your gas utility from outside and do not go back in until they say it is safe.

Is my furnace worth repairing?

Many furnace problems are routine repairs. If the furnace is old and the failure is major, your technician will explain the repair and the replacement option side by side.

More answers: heating and cooling FAQ

Contact us

Request Furnace Repair